Rider Central
Style
DR-Z400
Other DR-Z Models
Trading Post
I just got done writing this in response to a thread, and would like to put it to some good use. At some point in the future, I'll incorporate this...
To make the long story sort ...........http://www.drzforums.com/showthread.php?1096-AP-ADJUSTMENT.....questions! It all started from that thread. I...
do i have to rejet my carb if i switch to a K&N filter? my current setting (dynojet stage one setting): pj 25 dj needle 2nd clip from the flat...
I should have in my grubby mitts soon... a FCR39 w/ manifold and clamps off of a "good running 400e". I look at the info on the other nameless site...
This graph depicts similar gains when using a KLR650 CVK40mm carb on your DRZ. http://www.dynojet.com/graphs/KLR650_2120.jpg
Jim and I did a little bit of tweaking to Debi's carb, yesterday. In a few minutes, I'll have it ready to bolt back onto the cripple's bike. Pass or...
Hi all, I think there's something missing from my TPS, while fitting the NCYR needle today I messed around with the TPS, when I stripped the carb...
Thanks for steering me to the JD kit, its the best one I have seen and good instructions too. But I haven't seen one in years. I'm not going to...
Hi folks. I am the new owner of a brand new DRZ400sm. I've been reading TONS of forums about mods and the such and the one that comes by often is...
My apologies for not stopping in lately here at the site. Going through a not so much into the forums lately phase. I am having my Z rebuilt and...
I saw some crf250/450 diagrams and i saw that the 16037-MEB-671 vacuum plate for the carb slide pirice is between $58 to $65 ! That's a very good...
Re here. http://www.drzforums.com/showthread.php?1063-Next-adjustment I actually turned around on my way to work and went home it was that...
Hi, I'm a DRZ newb...I just bought a 2001 DRZ400e, and I'm sure the vacuum lines are being run improperly. See the pic below. The hose on the right...
Every since I changed jetting/fuel screw settings, due to addition of RS2, my cold start is different. For a cold start I always pull choke all the...
Refer this thread about the 155 jet http://www.drzforums.com/showthread.php?1046-Do-I-need-to-run-a-155-Main... Now let's assume for now its' a...
Hello guys. I installed an ap heavy duty spring (thanks again Lynk) on my fcr-mx to get rid of the annoying Ο-ring that get cut every now and...
Just recently I bolted up the MRd/SSW to my 434SM- FCR39MX-3x3. I've read how a 155 is suggested with a BB, do I really need to is my question. Sea...
Hi guys, I'm new to the forum. Smias talked me into registering to this forum. So here's how it goes. I've recently purchased a used FCR 39 MX (from...
Can someone post a purchase link for the JD kit. I have used the Alba, DJ and stock shimmed needle setups on my other 400s. But would like to try the...
Ok, you're gonna have to excuse my ignorance for blatently asking this, but my freaking head is spinning from reading all these threads and posts in...
well iam done with tuning the carb on the yz426f i got it from my 2005 drz400sm. an installed the fcr 39(stock yz426 carb) on the dr. i installed a...
I have read that removing the pilot air jet #100 is only for after market carbs like Sudco and not for carbs that came from a donor bike like yz426 ....
ok so i installed the fcr that was on my yz426f, on the drz, runs much better!!!! so i installed the Mikuni on the yz426. starts up good but runs...
Has any one use this kit in a drz400 with FcrMX ? Is it possible with this to change main+pilot jet without removing the carb from the bike ?...
help! help! help! just afer the installation of fmf power bomb header + power core 4, my bike starts backfiring "bang bang bang" in the exhaust when...
Anyone ever used one
A friend bought a used FcrMX41 for his future drz470 but these gaskets in the circle are destroyed ...
I have seen and read so many posts here and other places but especially here concerning jetting and stock carb upgrade. I have seen the advice from...
James and I have been chatting via email over the weekend. His needles are of great interest to me. While the NCYR (two taper) has been very good for...
So where do I send my vaccum hose from the fuel tank to the fcr carb?
Ok, so I ordered my MRD/ssw. I am going to keep the stock carb, atleast for now. Getting ready to order JD Jet kit. Just want to make sure I get the...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
